| If your keypad looks like this, use these instruction: |
Digital Wireless Keypad
00001033
|
|
|
|
|
|
|
Resetting your keypad
If, at any time, during programming, you should enter the wrong PIN or make a mistake, you should reset the keypad to its factory setting.
|
|
|
|
|
Open the keypad cover half way |
|
|
|
Press and hold the number 8 and the PROG buttons while opening cover fully. |
|
|
|
The indicator light will blink once and go out. |
|
|
|
Close the cover. You are now ready to re-program your keypad.
|
|
| Basic Programming |
|
|
|
|
Open cover fully Indicator will blink once on go out |
|
|
|
Press 3-5-7 |
|
|
|
Press PROG Indicator will blink once per second |
|
|
|
Enter PIN 1 (up to 8 digits) |
|
|
|
Press PROG Indicator will blink twice per second |
|
|
|
Close cover. Your keypad is now ready to be programmed to the garage door opener. |
|
|
|
Locate the Learn code button on your Intellicode/CodeDodger garage door opener. |
|
|
|
Depending on model, the learn code button will be located under the light cover or on the rear panel. |
|
|
|
Press the learn code button Learn code LED will flash |
|
|
|
Open cover on keypad fully |
|
|
|
Enter PIN number |
|
|
|
Press the SEND button 4 times, or until the door begins to operate. |
|
|
|
You will now be able to use your wireless keypad normally.
|
|
| Controlling a single door with your keypad |
|
|
|
|
Open keypad fully |
|
|
|
Press PIN number |
|
|
|
Press SEND once |
|
|
|
Door should operate normally
|
|
|
NOTE: As a "panic" feature this keypad will operate door for up to 30 seconds from any button. |
|
|
Programming multiple doors with your keypad
Program your keypad according to the steps outlined in the Basic programming section listed above. |
|
|
|
|
|
|
|
Open cover fully |
|
|
|
Enter PIN number |
|
|
|
Press PROG Indicator will blink once per second |
|
|
|
Press PROG Indicator will blink twice per second |
|
|
|
Press PROG indicator will blink three times per second |
|
|
|
Enter the total number of doors (2 or 3) |
|
|
|
Press PROG |
|
|
|
Close cover |
|
|
|
Your keypad is now ready to be program to the garage door openers. |
|
|
|
Locate the learn code button on your garage door openers |
|
|
|
Press the learn code button once Learn code indicator will flash |
|
|
|
Open cover on keypad fully |
|
|
|
Enter PIN |
|
|
|
Press SEND |
|
|
|
Enter door number 1-2-or-3 |
|
|
|
Press send button 4 times, or until door operates |
|
|
|
Repeat these steps for door 2 and 3
|
|
| Controlling multiple doors |
|
|
|
|
Open cover fully |
|
|
|
Enter PIN number |
|
|
|
Press SEND |
|
|
|
Enter door number (1-2-or 3) |
|
|
|
Chosen door should operate
|
|
|
Adding PIN 2 |
|
|
|
|
Open cover fully |
|
|
|
Enter 1-5-9 |
|
|
|
Press PROG Indicator will blink once per second |
|
|
|
Enter PIN 2 (up to 8 digits) |
|
|
|
Press PROG Indicator will go out |
|
|
|
Close cover |
|
|
|
Your keypad is now ready to be programmed to the garage door opener. See steps in Basic programming.
|
|
| Adding temporary PIN |
|
|
|
|
Open cover fully |
|
|
|
Enter PIN 1 |
|
|
|
Press PROG Indicator will blink once per second |
|
|
|
Press PROG Indicator will blink twice per second |
|
|
|
Enter temporary PIN |
|
|
|
Press PROG Indicator will blink three times per second |
|
|
|
Close cover |
|
|
|
Your keypad is now ready to be programmed to the garage door opener. See steps in Basic programming.
|
|
| Canceling the temporary PIN |
|
|
|
|
The temporary PIN will remain active until PIN 1 is entered.
|
|
| Changing a PIN |
|
|
|
|
Open cover fully |
|
|
|
Enter PIN to be changed |
|
|
|
Press PROG. Indicator will blink once per second |
|
|
|
Enter new PIN |
|
|
|
Press PROG |
|
|
|
Indicator will blink twice if PIN 1 has changed or go out if PIN 2 was changed. Close cover. Your keypad is now ready to be programmed to the garage door opener. |
|
|
|
Locate the Learn code button on your Intellicode/Codedodger garage door opener. Depending on model, the learn code button will be located under the light cover or on the rear panel.
|
|
|
|
|